The following symbols are used in this user manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. Factory setting: audible signals activated. Setting mode The appliance is in setting mode when all programme lights are illuminated. Carefully push the clips so that the control box detaches from the top panel. As a backup, I intend to look up a replacement relay and be ready when the repair brakes again.Next
With this appliance you will experience the perfect combination of functional design and cutting edge technology. Both the Auto 65º and the Auto Bio 50º will flash and the buttons can be released. It looks like a small black box, and by comparing it to the position of the legs on the back side of the circuit board showing in the picture , you can find the right legs to resolder quite easily. In this case, to return to setting mode, the programme has to be cancelled. Carefully pull out the top panel a bit by pulling towards yourself.Next
It is possible to deactivate the audible signals, using the function buttons. Press and hold the Auto 65º and the Auto Bio 50º buttons. It is a good idea to solder all of the relay's legs while you're at it anyway. Press and hold the Auto 65º and the Normal 65º buttons. Watch the lever green arrow as it gets free from the opener.Next
To memorize the operation, switch off the dishwasher. Put it all back together and it works! The programme has been cancelled and the machine is now in setting mode. If you look at the circuit board you'll find the relay itself on the other side where all the components are. To activate again the audible signals, simply follow the above operations until the End of programme indicator light illuminates. At the same time the End of programme indicator light illuminates indicating that the audible signals are active. Once out I could see no obvious problem with the relay soldering, but I re-soldered it anyway as suggested. In addition to this you find environmental and energy saving aspects as an integral part of our products.
Unplug the power switch blue circle carefully so you don't break the wiring. Repairs carried out by inexperienced persons will cause injury or serious malfunctioning. Dishwasher broke down 5 days before Christmas - not heating the water. The box is similar but getting it out was a bit different. After unclipping the control box, carefully pull it out a bit to get access to the cable connectors at the back.Next
To ensure optimal and regular performance of your appliance please read this instruction manual carefully. Watch for the power switch cables pointed out with the blue circle in the picture and the door opener lever green arrow in the picture. Comply with the safety instructions of the dishwasher detergent manufacturer. The problem can easily be fixed by just resoldering the broken connection. It was not seen that the contacts are bad.Next
For electrical and water connection carefully follow the instructions given in specific paragraphs. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety. . Contact your local Service Force centre, in order to avoid hazard. Never connect a damaged machine. Take note of the order and placing of the different connectors before unplugging them so that you don't forget in which order they should be inserted back after the repair. General information and tips Environmental information Contents 3 Contents Operating instructions 5 Safety information 5 Correct use 5 General safety 6 Child safety 6 Installation 6 Product description 7 Control panel 8 Setting mode 9 Audible signals 9 First use 10 Set the water softener 10 Setting manually 11 Setting electronically 11 Use of dishwasher salt 12 Use of rinse aid 13 Adjusting the dosage of rinse aid 14 Daily use 14 Loading cutlery and dishes 15 The lower basket 16 The cutlery basket 17 The upper basket 18 Use of detergent 19 Fill with detergent 19 Use of combi detergent tablets 20 4 Contents Cleaning the filters 24 Cleaning the spray arms 25 External cleaning 25 Internal cleaning 25 Prolonged periods of non-operation 26 Frost precautions 26 Moving the machine 26 What to do if.
But I refreshed the contacts with a soldering iron. Different speeds are used during the wash cycle, depending upon which part of the program is being performed. The softener should be adjusted according to the hardness of the water in your area. I also re-soldered one of the spade connectors to the board the end one. Resolder the legs pointed out by the yellow arrows too, so you don't have to open the dishwasher up again soon. This sensor is actioned by a very weak magnet in one end of the middle spray arm.Next
We wish you much joy with your new appliance. My biggest problem was that the relay pin was mostly gone as well. The first measurement takes place 13 minutes after the start of the heating step and the second measurement is taken 10 minutes later, 23 minutes into heating. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. In this case the copper track was burned so bad, that I had to solder a small piece of wire by the red arrow in the picture to make contact between the relay's leg and the copper track.Next
To refer to this manual any time you need to, we recommend you to keep it in a safe place. Set the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. In this way you will avoid anybody tripping over the open door and hurting themselves. Press button C, the lights of buttons A and B turn off while the light of button C goes on flashing. Thank you very much to the author of the article! Press and hold buttons B and C until the light of the buttons A, B and C start flashing.Next