Dsc pc 3000 programming manual. DSC PC3000 INSTRUCTION MANUAL Pdf Download.

Dsc pc 3000 programming manual Rating: 9,6/10 499 reviews

AlarmsBC presents user manual pc

dsc pc 3000 programming manual

The Master Code may be changed but it must not be removed. The feature is automatically disabled when the panel is armed and disarmed. They would be used for zones that require an extra long entry or exit delay time; for example, an overhead garage door. If the zone light is on, that user can bypass, if that zone light is off, that user cannot bypass. Install keypads and connect wires to keypad terminals on panel.


Next

Dsc pc2550 programming manual

dsc pc 3000 programming manual

Zone Bypassing Access Code When the system is established for split arming, user zone bypassing should be set so that bypassing requires the use of an access code. Note: A relay must be used to obtain more current. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of Digital Security Controls Ltd. Your installer will tell you which commands listed in this manual apply to your system. Keypads are mounted in convenient areas close to the exit-entry doors.

Next

DSC PC3000 Keypad Instruction manual PDF View/Download

dsc pc 3000 programming manual

Revise the plan as conditions change; for example, when there are more or fewer family members in the home, or if there are changes to the house. The reporting codes must be 2 digits in length and programmed as follows. Provide user with the Instruction Manual and instruct them to read the manual to become familiar with the system operation. The metal cabinet contains the system electronics, fuses and stand-by battery. The keypad is normally resting in the arm-disarm mode. The account code must be four decimal digits in length and in the range of 0001 to 3374. The Master Code will be supplied to you by your installer.

Next

DSC PC3000 Keypad Instruction manual PDF View/Download

dsc pc 3000 programming manual

If the keypad is responding normally, connect the battery. In no event shall Digital Security Controls Ltd. Le Ministère n'assure toutefois pas que le matétiel fonctionnera à la satisfaction de l'utilisateur. The added areas include: basement, bedrooms, dining rooms, furnace room, utility room and hallways not protected by the required detectors. However, there is no guarantee that interference will not occur in a particular installation.

Next

AlarmsBC presents user manual pc

dsc pc 3000 programming manual

Les réparations de matériel homologué doivent etre effectuées par un centre d'entretien canadien autorisé désigné par le fournisseur. It is essential that escape from a bedroom be possible without opening the interior door. They also have entry delays provided that a delay zone has been tripped first. Press any key within 30 seconds of first alarm to get 2 minutes to reset smoke detectors. If after signal silence, the smoke detector is not restored to normal, the signals will resound after 90 seconds, and 30 seconds after that, the communicator will transmit. This trouble is cleared when the trouble display is viewed and exited or when an attempt is made to reset the internal time of day clock. The user does not have to manually bypass the home-away zones.

Next

DSC PC3000 INSTRUCTION MANUAL Pdf Download.

dsc pc 3000 programming manual

Transmission of the fire alarm to your monitoring station is delayed for 30 seconds to allow you to cancel possible false alarms. Remember if no keypad entry is made for more than 2 minutes the keypad will return to the normal arm-disarm display and the complete command will have to be re-entered to program a new access code. For example, open a door or window. The alarm memory will automatically be displayed when the system is disarmed see Disarming. To reset smoke detectors to normal, first clear all products of combustion from the detectors. . All 24 hour and fire zone transmit immediately.

Next

Dsc Pc3000 Programming Manual Dsc Pc3000 Programming Manual PDF Download Free

dsc pc 3000 programming manual

Arm the panel, wait for the exit delay to expire and trip a detector on an instant circuit. The feature is turned off if the keypad sounds one long beep. If your security system is programmed to report to a monitoring station, the keypad will also sound a tone to indicate that the monitoring station has been advised of the arming of the system. Auto-arm - no bell squawk Auto-arm - bell squawk Off Zone Light 2. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. It is thus very important that a family escape plan be developed and rehearsed.

Next

Dsc pc2550 programming manual

dsc pc 3000 programming manual

Quick Arm may be used as a convenience for regular users or when the sytem is to be armed by individuals who are not authorized to disarm the system. The keypad should beep several times to indicate acceptance of the master code. A battery trouble will be displayed and can be reported if the battery is weak, disconnected or the battery fuse is blown. Auxiliary Power Supply Trouble reporting code is sent when the auxiliary power supply fuse failed. Zone Light 3 Zone Light 4 Zone Light 5 Zone Light 6 Zone Light 7. If you exit within the allowed exit lime, the system will automatically reactivate the interior zones. Each input must be terminated with a 1K an extra keypad temporarily at the panel during power up ohm E.

Next

AlarmsBC presents user manual pc

dsc pc 3000 programming manual

When the proper keys are pressed the keypad sounder and the programmable output are activated for 5 seconds. The red battery lead attaches to the positive battery post and the black battery lead attaches to the negative battery post. If zone light is on in both sections, the code is common to both sides and will arm or disarm the entire system. Set short exit and entry times for testing. Also, damaged wiring or contacts on a zone may be temporarily bypassed until repairs can be made so that the panel can be armed. Common Access Code If an access code 1 through 8 only is assigned to Group A and Group B then that access code will arm and disarm the entire panel. When the system is disarmed using one of the access codes, the corresponding reporting code in this section is transmitted.

Next